Honda Twins banner

Spraymax 2K clearcoat

1 reading
36K views 13 replies 7 participants last post by  bilbikek411  
#1 ·
I haven't posted on here much, but I thought I'd share my experience with Spraymax 2K clearcoat (spray can). I used it on a Z50 hardtail project I've been working on and it's no joke. Nice spray pattern, and it seems to stay consistent all the way to the very end of the can. I have a decent HVLP gun but I didn't feel like dropping $75+ on clear just for a minibike, since that seems to be the minimum cost once you buy hardener, reducer, etc. I also didn't want to deal with cleaning the gun, I'll admit it. Anyway, it turned out really well. I used dupli-color metalspecs blue as a base, then some airbrushing using silver metallic decanted from a spraycan. I very lightly went over airbrushed sections with white scotchbrite to knock the edges down, wiped with grease&wax remover and went at it with the clear. One can was enough for two coats on the frame, tank, fork uppers, headlight bucket, fiberglass tailsection, and an open-face helmet. It was dry to the touch within about two hours and really looks good. I'm not an expert painter by any means, but I just laid it on wet enough to flow out nicely and get good gloss, had no problems with runs or anything else. There are some dust specs if you look closely, but I don't have a booth, just my regular workshop. You definitely want to wear a good respirator with this stuff though! Since it's catalyzed, it is suppesed to be pretty fuel-resistant. I might wait a week or so then splash some gas on my test panel to see how it holds up. Anyway, if you have a small project and you're looking for an economical but high-quality clearcoat without all the usual equipment required, this stuff is the way to go. It's not cheap (I think it was about $18 a can plus shipping) but definitely worth the cash. I might buy a couple more cans before someone from the gov't finds out how good it is and bans it. I got it here:

http://www.sgcardetail.com/USC-3680061-SprayMax-2K-Glamour-High-Gloss-Aerosol-Clear-Prodview.html

I'll try to post some pics once I have the bike together, event though it's not a twin!
It's not often that a product really exceeds my expectations the way this stuff did. I have no affiliation with the vendor or the manufacturer, I'm just really impressed.

Steve
 
#3 ·
This is probably the best rattle can clear coat available.

I would highly recommend to read the instructions on the can and wear protection that you would not normally wear when using a spray can. Almost every time I used this stuff I got sick for a couple days after. I recently bought a nice quality respirator, and have not gotten sick since. I also cover as much of my skin as possible when using this stuff now as well. From what I understand and have read it can be absorbed through the skin very easily with adverse reactions.
 
#4 ·
I didn't think about the skin exposure at first, but then after a while I could feel it on my forearms. I wiped them off with acetone, not sure if that's a good idea, but no way is soap and water gonna touch this stuff. I'll wear long sleeves next time. I didn't wear safety glasses because I just can't see well enough to do a good paint job with them on. I was wearing nitrile gloves and a good respirator at least. My wife came out in the shop as I was spraying and I kicked her out. I had windows and garage door open but no point in taking chances. I couldn't smell anything with the respirator on, but when I took it off outside I could definitely smell it. Point is, don't mess around with this stuff, it's not like normal rattle can fumes where you're lightheaded for a few minutes. You can do permanent damage breathing this in.

I'll try to put a pic on here.
 

Attachments

#7 ·
Thanks for the props, guys. I got a cheap HF airbrush a month or so ago and just started messing around with it. It actually works pretty well, or else I just don't know any better because it's the only one I've ever used. I"m really not an artist, so I'm kind of limited to geometric shapes and that sort of thing. Besides, my wife won't let me paint a "Wizard battle in the mountains" scene on her van. (She won't let me put side pipes and a wing on it either.)
For this Z50 I'm doing kind of a vintage roadrace thing. Laid up the glass tail on the back of a Suzuki JR50 tank, made lower handlebars, and some other stuff. It should be pretty cool when I get it put together. It will definitely be one of a kind, at least.

Steve
 
#8 ·
Do they sell this at any of the big box parts stores (i.e. O'Reilly, Advance, AutoZone, etc.) ?
 
#9 ·
I have to dig this thread up from the deeps. :)

I just finished clear coating my tank, oil cover and seat with Spraymax2K Glamour Clear Coat and I'm blown away with the results. It goes on so smooth, even when dry it looks wet and deep. Amazing. I'm used to using Dupli-color and always have to wetsand and polish it to get it flat, not with this stuff, I can just install as is. A lot more expensive than Dupli-color but well worth it for this shine and extra protection.

I'll post some pics when I can. Haven't seen it out in the sun yet, hoping it'll clear off this weekend.

I have to paint a few parts for one of my other bikes this winter. I painted it before using Dupli-color but couldn't get a good colour match. This time I'm going try the Spraymax colour match to see how close they can get.
 
#14 ·
I want to ask if any of you have used it on aluminum hubs ? I'm in the process of cleaning off some corrosion on my CB350 front drum brake hub w/ red scotchbrite and want to know if this Spraymax 2K clear will stick to the cast aluminum of the hub w/o any type of primer,etc. I like to keep that 'alloy' look to the hub w/o having it get corroded when I hit some rain,etc. I enjoy the original factory clear coat that Honda put on when they assembled the bike new but now that is all worn/weathered off.
Let me know,ok ?