Honda Twins banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 132 Results
  1. Member Introductions
    Hey everyone. New member here from LA. Bought a non op 360 a few months ago and in the process of fixing it up to my personal tastes. It's already undergone a lot of changes, including having been stolen and recovered a few weeks ago. Looking forward to sharing some knowledge I've gained, and...
  2. Fuel Supply and Carburation
    I’m sure this has been asked numerous times but the only solution seems to be cmc for these throttle shaft plugs does anyone else have a source on where to get them since cmc has not sold them in quite some time.
  3. Engine Discussion
    Baffled by an issue, and my limited understanding of the drivetrain isn’t helping. Put bike in Neutral: light comes on, Can freely roll the bike. Cannot turn the engine with the Kick (wont’ budge) Cannot turn engine at stator Pull in clutch lever (leave in Neutral) light comes on, Can...
  4. Member Introductions
    Pulled the trigger on a '75 CB360T recently as my first motorcycle. The bike is in solid condition for being over 45 years old. When warm, she runs like a dream, but the problem lies in getting her there. Cold starts are tough, as I have had to push start the last couple times I've fired it up...
  5. Frame, Suspension and Steering
    I've removed the front fender as part of my cafe racer conversion to my '75 CB360. As such, I'm thinking the bike could use a fork brace to compensate. The internet has failed me, turning up nothing pre-made for the 360, and barely any posts/discussion about it. I'm still running the stock front...
  6. Project Logs
    This week I've started my new project on a 1974 Honda Cb360. I got this bike about 5 years ago in rural Iowa out of an old, decrepit barn that was nearly falling over. A family friend offered the bike to me for free, so I gave him $1 for it. I loaded it up and took the dust ball back to my...
  7. Member Introductions
    Hi all, I'm Howard Roark, I haven't felt like I had the knowledge to add anything useful on bikes, and I probably still don't but also to this point everything has ran pretty smoothly. I'm in Utah, USA and have a '74 CB360. Love my bike, it's a total blast. Thanks for having me on the forums...
  8. Member Introductions
    Hello all, I have been on the forum reading everyones posts and it has been extremely helpful in working through this project. I bought a 1974 CB360 for 400$ that had not ran in many years. Thanks largely to this forum it is running and mostly wired and soon to be registered and back on the...
  9. Engine Discussion
    Hey all. I've posted before regarding this sound but am posting a link to a video I've just recorded of it for clarity. Something isn't right, right? I've got another kickstarter shaft in a box of miscellaneous from the PO. Can't be certain, but looks to be in good nick. I also just did a...
  10. Engine Discussion
    Hey fam. Would anyone care to take a listen to this video and put my mind at ease? youtu.be/wfpOQ2MiNPY NOTE: the fuel is turned off so the thats why the bike isn't starting. Back story is i bought this cj/cb360 about 6-7 months back. The motor is cb. I think the serial numbers are part of...
  11. Miscellaneous Discussion
    Hello All, A few months ago I purchased a 1976 restored CB360. I have never owned a motorcycle and really didn't care to besides these vintage cafe/brat updates. It's awesome. My question is: any tips or advice to enhance or upgrade the bike such as - "use these filters" "add this to your gas"...
  12. Engine Discussion
    Hey everyone, Just got into my Crankcase on my CL360 to find that the kickstarter spring busted off a chunk of the lower case. I have a donor CB engine, but would like to use as much of the original CL360 engine as possible. Is it an option to just replace the lower case from the donor? Or is...
  13. Miscellaneous Discussion
    Hi everyone! I'm new to this forum and so far I've been impressed by the wealth of information here. I recently purchased a 1974 CB360 in pretty good condition. When I start it up, I'm getting some backfire and it wont stay idling. The previous owner had mikuani carbs installed and...
  14. Electrical Issues
    Hello all! I'm working on my first bike build and am a serious rookie when it comes to wiring! I recently grabbed a 76 CB360T with 10k miles, but the bike hasn't run 20 years. Bike ran when it was parked, but then sat in an indoor storage facility. I started with the typical tear down, oil...
  15. Engine Discussion
    With Covid closing everything down this summer, I decided to pull out my dad's CB360T that had been sitting in the barn for nearly 40 years. Externally, it wasn't too bad with rust in some places, but no holes. The engine appears to be in great shape internally, and also has plenty of...
  16. Parts For Sale
    1976 Honda CB360T Motorcycle Gas Tank | eBay Contact via eBay if questions please.
  17. Project Logs
    Hi, this is my first project here and first motorcycle project in general. Usually work on dirt bikes. Really loving working on the old bike though. Picked up this 1975 Cl360 with around 8k miles. Overall not in bad condition just a lot of surface rust. Wasn’t running so I got it for $600 bucks...
  18. Engine Discussion
    I bought my first bike a little over a week ago it's a gorgeous 1976 CB360. When I bought it the electric start was bad but it was kicking fine which was well enough for me. I've started it up and practiced on it five times since I bought it and it took more and more effort to start each time...
  19. Member Introductions
    hello , new here im from orting wa. I sometimes enjoy working on the bikes and sometimes I do it for reasons unbeknowings to me! this is my second cb360 bike (3rd motor) . most of the projects ive done start out with intentions of low budget low cost and it usually goes up from there. the...
  20. Tires, Wheels, and Brakes
    Bought this 1976 cb360t with essentially the entire front disc brake assembly missing. currently in the process of buying the parts I need to rebuild the front brake from the ground up. So far I’ve successfully gathered all the caliper parts, master cylinder, brake lines, three way joint, banjo...
1-20 of 132 Results
Top