Honda Twins banner
brake
1-19 of 19 Results
  1. Electrical Discussion
    Hello, Newbie on the forum with limited experience working with bikes. To start when i first got the bike the brake lights were functioning. Last weekend I noticed the front brake electrical wire (not cable) was out of its socket. The one pin was also loose and required me to hot glue gun...
  2. Tires, Wheels, and Brakes
    Bought this 1976 cb360t with essentially the entire front disc brake assembly missing. currently in the process of buying the parts I need to rebuild the front brake from the ground up. So far I’ve successfully gathered all the caliper parts, master cylinder, brake lines, three way joint, banjo...
  3. Tires, Wheels, and Brakes
    Cm250tb had the handle bars like the rebel, I think they are called Chumps? Because of the requisite motorcycle arm injury I found the throttle angle to my wrist very uncomfortable. So I bought a tracker bar. The issue is that the brake fluid reservoir now sits at a jaunty angle. I can leave...
  4. Tires, Wheels, and Brakes
    I bought a Hawk missing its front brake hose, anyone have a measurement on how long it needs to be so I can order an aftermarket part? Any help is greatly appreciated.
  5. Electrical Discussion
    How do Despite having torn down my CL77 to it's frame and component parts over the last week or so, it's only just occurred to me that neither it, nor the CA77, have a front brake switch. I assume that the law changed sometime in the late 60's 'cos the SL350 K0 has a switch built into the...
  6. Tires, Wheels, and Brakes
    Is there a modern caliper that can be swapped in for the old asbestos front brakes? The old calipers are stuck and worn all the way down.
  7. Electrical Discussion
    I recently dumped all my wiring into a bucket under the seat.... or what I could get into it. Everything works and runs except the brake light. Mystery. It worked up till the mod. I traced the green/yellow and black wire to the brake swtich/spring to their proper mates in the main harness but...
  8. Tires, Wheels, and Brakes
    Hello Hondatwins, I did an introduction to this bike when i joined the forum a few years back, but life happened and it ended up stored for about 3 years. Since a few weeks i have been working on my (European) 84 cm400t, getting it back to riding condition. Even after years of neglect the...
  9. Parts For Sale
    This is for the 1980 400E, so it's got the perch for the front brake (drum brakes) lever, the kill switch and the starter switch. It's in good condition. The wires and brake lever switch are good. PM for pics. I'd rather just text pics than get them on my computer.
  10. Parts For Sale
    Complete assembly, came off low mileage bike, chrome in good shape. $100 shipped
  11. Wanted Parts and Bikes
    Looking for a CL450 front drum. Entire wheel, only drum, doesn't matter... show me what ya got. I check ebay often, but figured I'd post here to see if anyone was holding anything. Thanks ya'll
  12. Tires, Wheels, and Brakes
    Hey all, I took the bike out yesterday and a few blocks from home I heard a noise and then instantly lost the use of my rear brake, the pedal locked in place. I got home to discover that the retaining bolt which holds the outer case of the drum brake at the 6 o'clock position had fallen out...
  13. Tires, Wheels, and Brakes
    Hello All. So I have just started putting together my CB360 project (I bought it from the PO in pieces). I is my first build and I did not realize that the PO cut the brake pivot off - I'm guessing to go with rear sets and a cleaner look. Sooooo, I purchased slipstream bolt on rear sets and...
  14. Tires, Wheels, and Brakes
    I would like to upgrade to a stainless line, but the only ones I can find online range from 18"-34". I measured mine at 48". Is that right? I cannot find one that long to save my life. I'm new to this, so I'm learning more and more each day.
  15. Tires, Wheels, and Brakes
    Hello all, I can't seem to find any post on something like this, probably because everyone keeps up with their parts during a bike tear down, but my rear brake torque arm managed to grow legs and hide somewhere in my garage during the reassembly of my 83 nighthawk 450. The only purpose of that...
  16. Tires, Wheels, and Brakes
    Greetings, I have a 1978 cb125s and I am attempting to fix the front disc brake. I am specifically looking for part# 45320-397-720 or 45320-324-700. All the parts places I have contacted online no longer have these parts available. I would be interested in buying the parts I need if anyone...
  17. Tires, Wheels, and Brakes
    Hello everyone! It has been awhile since the last time I posted, but I have hit a brick wall with a brake issue so I figured I would ask the experts. I recently rebuilt my front master cylinder (everything labeled 25): However, brake fluid is still leaking from the piston/brake lever and when...
  18. Miscellaneous Discussion
    Hey all, Finally getting around to installing my rearsets. The shifter side I have planned out fairly straight forward: drill into the gear shift lever, angle it upwards and attach with threaded rod and heim joint. But the brake side has got me pretty stumped. As you all know, the K5 is one of...
  19. Tires, Wheels, and Brakes
    Sorry if there was already a post on this - I'm not finding an exact thread to count on. I'm about to order new brake pads for the front disk and rear drum and wasn't certain on which brands to go through. Bike Bandit shows up with a number of brands I'm also not certain which ones would be...
1-19 of 19 Results
Top