Search Results - HondaTwins Forums

Search:

Type: Posts; User: Yendor

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    3
    Views
    119

    A correct center stand for the CL Model looks...

    A correct center stand for the CL Model looks like this:

    Note the TAB in the middle of the mounting bolt tube.

    286026
  2. Replies
    5
    Views
    122

    Herr Decan is 100% Correct. That is the VENT for...

    Herr Decan is 100% Correct.
    That is the VENT for the float bowl.
    Take a can of Carb Spray Cleaner to it and it will come out of the Brass Nipple on the other side.
  3. Sounds like an incorrect O-Ring. There is no...

    Sounds like an incorrect O-Ring.
    There is no movement to that part -or- at least there should not be.
    Unless it moves it should not wear.
  4. Replies
    14
    Views
    238

    Soak It in Kerosene overnight. Then let it...

    Soak It in Kerosene overnight.

    Then let it dry, and soak it in HOT Oil.
    (If you live in a warm area you can just leave it out a BLACK Oil Drain Pan out in the sun for a day).
  5. Replies
    23
    Views
    454

    CMNSL Has the Parts you are looking for in stock....

    CMNSL Has the Parts you are looking for in stock.
    Their shipping is a little costly but you coujld also try David Sliver Spares they have a US Warehouse in PA.

    Here is a Link to the CL 350...
  6. Replies
    4
    Views
    84

    Did you check the FUSE? It lives in a holder...

    Did you check the FUSE?

    It lives in a holder just to the front of the battery.
    15 AMP - METRIC - Not just any Fuse from an Auto Parts Store. Any Honda Dealer has them in stock - Get spares.
    The...
  7. If your bike ran with the advance they way you...

    If your bike ran with the advance they way you said - it is right.
    If it is 180 Out it will NOT run. - PERIOD - Will not RUN.
  8. I agree this sounds more like a Carb Float...

    I agree this sounds more like a Carb Float Adjustment or a Timing Adjustment.

    The Carb Float could be allowing excess fuel to carbon up the plug then when carbon coated not firing well and gas...
  9. Replies
    8
    Views
    132

    Multiply by (4X). If the meter is calibrated to...

    Multiply by (4X).
    If the meter is calibrated to give you the RPM of (4) Pulses per CYCLE and you are only provideing an Input of (1) Pulse per cycle then Multiply by (4).

    Should work but the...
  10. Replies
    22
    Views
    375

    UUMMMM.... If the Stator COVER was NOT installed...

    UUMMMM....
    If the Stator COVER was NOT installed it is going to leak.
    As Steve said there is supposed to be oil in there to splash around and provide libe to the starter chain.

    That is why when...
  11. Wood Bleach. 285290 It is basically Oxcalid...

    Wood Bleach.

    285290

    It is basically Oxcalid Acid which loves to attack RUST but will not harm the chrome.

    Mix it up in a Plastic Storage Box that will hold at least 1/2 of the fendrer under...
  12. They make extended lenght aircraft drills here is...

    They make extended lenght aircraft drills here is one source:
    This one is for a full set they are 12" in lenght and start at 1/16"
    ...
  13. Replies
    15
    Views
    301

    I'm not a fan of the PAMCO EI System, and YES I...

    I'm not a fan of the PAMCO EI System, and YES I have had expirence with him.
    Right after he changed the Rotors but before the Electronic Advance system I had ordered his system.
    I emailed him about...
  14. Replies
    6
    Views
    136

    The LINK I posted will take you directly to the...

    The LINK I posted will take you directly to the CMNSL Page for the CL350 K0 parts listings.
    Did you go there?

    I acquired a set of early CL pipes and ordered the Longer Split Collar Sleeve and...
  15. Replies
    6
    Views
    136

    You apparently have a VERY EARLY set of CL pipes....

    You apparently have a VERY EARLY set of CL pipes.
    The reinforced ends of the header pipes changed in '70 and they were made longer.

    With the pipes that have the short reinforced ends the (2)...
  16. Is there an ON-LINE Link?

    Is there an ON-LINE Link?
  17. Replies
    5
    Views
    142

    350's are 350's pretty much all models all years....

    350's are 350's pretty much all models all years.
    The differences are very small and 95%+ of the parts will swap from one to another.
    Same for adjustments etc.

    What do you need help with?

    PS:...
  18. Replies
    4
    Views
    113

    The HEADER Pipe looks right but that is not an...

    The HEADER Pipe looks right but that is not an OEM Muffler.
    Looks more like a Harley muffer.

    The VERY Early Bike had 6 mm Studs and had a Short Reinforcement section at the Gasket end if the...
  19. (2) Questions: Is the Choke - "ON"? Are you...

    (2) Questions:

    Is the Choke - "ON"?

    Are you letting it overheat while playing with it?

    These are Air Cooled motors and don't really like to be running too long standing still.
    The Simple...
  20. Replies
    9
    Views
    195

    Or buy a wooden dowel rod at home depot and use...

    Or buy a wooden dowel rod at home depot and use it and a hammer to push it out.
    The wood might mush up but it wont' damage the metal.
  21. Replies
    4
    Views
    133

    I think you have a lot of machine work ahead of...

    I think you have a lot of machine work ahead of you.

    But... with that said I suspect you could machine it out and add some type of sleeve that would make it all fit.
    You just need a skilled...
  22. Where are you adjusting the Idle Speed? Your...

    Where are you adjusting the Idle Speed?

    Your original post mentions using a CABLE TYPE Adjuster?

    There should be a Spring Loaded (to hold tension) Idle Speed Screw on the end of the Throttle...
  23. Replies
    7
    Views
    132

    I can see one of yor fears is the process of...

    I can see one of yor fears is the process of removing and re-installing the motor in the frame.

    This has been done single handed by many here, by laying the morotr on its side and lowering the...
  24. Replies
    13
    Views
    216

    If you are replacing them remember that on is a...

    If you are replacing them remember that on is a SHOULDERED Bolt to insure proper alignment of the Cam Sprocket.
  25. Thread: 1972 cl 350

    by Yendor
    Replies
    15
    Views
    584

    I think most of the previous posters mmissed your...

    I think most of the previous posters mmissed your finding Compression: "140 lbs compression both sides"

    A healthy 350 has 180-185 PSI on both side with less than 5% variation.

    The FSM spec's...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4