View Profile: f100owner - HondaTwins Forums
Tab Content
  • f100owner's Avatar
    11-10-2019, 01:28 PM
    Did not use the Common Motor diaphragm, and replaced both of mine with ones from 4into1. Basically cut out the old and used a box cutter blade to...
    7 replies | 103 view(s)
  • f100owner's Avatar
    11-07-2019, 10:33 AM
    no direct documentation from manufacturer/seller was available that I could find at 4into1. Online searches obviously included the common motor...
    7 replies | 103 view(s)
  • f100owner's Avatar
    11-07-2019, 09:37 AM
    When replacing the diaphragm with the original style does one use any cement to secure the replacement to the slide. I suspect when originally...
    7 replies | 103 view(s)
  • f100owner's Avatar
    11-07-2019, 07:38 AM
    I have taken my 350Cl up to about 60-65 and held it there for a short time - a couple of miles - but it was not enjoyable by any means. At that ...
    29 replies | 355 view(s)
  • f100owner's Avatar
    11-06-2019, 10:52 AM
    f100owner replied to a thread K0 CL350 project in Project Logs
    Went ahead and ordered "both" types of diaphragms for my carb repair. I hope to be able to use the original style, but have the other style in the...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-31-2019, 12:25 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    thanks for the information. Since the diaphragm acquired does not have a "tab" for alignment, I am thinking the super glue might help retain the...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-30-2019, 06:41 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    As to replacing the diaphragm is the procedure documented here http://jbmindustries.com/Yamaha650.html an acceptable approach? This way does it by...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-27-2019, 06:23 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    I could not imagine I missed a torn diaphragm during the carb rebuild. Went back and looked again. A previous owner had attempted a repair using...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-26-2019, 05:53 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    Found a problem that might be contributing to my acceleration/deceleration issues. Torn diaphragm on my left carb. Was replacing accelerator cable...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-24-2019, 01:17 PM
    Plugs looked a lot like mine after about 300 miles on a top-end refresh.
    4 replies | 97 view(s)
  • f100owner's Avatar
    10-23-2019, 01:40 PM
    I am going to assume the answer is yes, but have located a luggage that was supposedly off a 72/73 CL350. While it ain't pretty, it does pretty well...
    0 replies | 40 view(s)
  • f100owner's Avatar
    10-22-2019, 09:59 AM
    f100owner replied to a thread K0 CL350 project in Project Logs
    I will say, since lowering idle speed, I am not getting near the "high idle" symptoms as before based on a couple of rides. Deceleration is not...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-21-2019, 09:11 AM
    I was hoping to find some bikes from my youth. My first bike was a red Allstate motor scooter. Did not run across one of those. My second bike, at...
    2 replies | 73 view(s)
  • f100owner's Avatar
    10-21-2019, 08:40 AM
    Pretty cool event, the Harvest Classic was. They take over the entire town of Luckenbach (a bar, dance hall, grounds) and throw a pretty good show....
    2 replies | 73 view(s)
  • f100owner's Avatar
    10-20-2019, 10:07 AM
    f100owner replied to a thread K0 CL350 project in Project Logs
    I understood your point. One of the guys there brought up Steve's name without me even mentioning it saying he had been a ton of help for his cl450....
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-20-2019, 09:49 AM
    f100owner replied to a thread K0 CL350 project in Project Logs
    Was visiting with him face to face while exploring the vintage bike show and rally this weekend. Telling him of my current challenges. He still...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-19-2019, 11:12 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    Fiddled a little with bike and the fast idle issue not as prevalent. At the recommendation of the Common motor guru, I lowered the idle speed as he...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-18-2019, 07:39 AM
    f100owner replied to a thread K0 CL350 project in Project Logs
    New intake manifolds, but will check for leaks again using a propane torch. as to resyncing them, I suspect my issue might be there and/or my...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-17-2019, 07:02 PM
    f100owner replied to a thread K0 CL350 project in Project Logs
    Well I officially suck at carbs. Pulled both carbs to oil the felt gaskets around the accelerator shaft. It seems worse and without really warming...
    316 replies | 10835 view(s)
  • f100owner's Avatar
    10-15-2019, 01:58 PM
    In the summers my parents would drag me to Lake Texoma on the OK side for a month or two long reunion. Two of my older cousins had Honda 50s - one...
    36 replies | 724 view(s)
  • f100owner's Avatar
    10-15-2019, 07:11 AM
    I know when I opened the headlight on my cl, it made me cringe. My first thought was how hard would it to be to swap out to a wiring or terminal...
    9 replies | 157 view(s)
No More Results
About f100owner

Basic Information

About f100owner
Biography:
Been riding Harley touring bikes that last few years. Acquiring a 68 CL350.
Location:
Central Texas
Interests:
Riding bikes and bicycles, shooting, working on old Ford truck
Occupation:
Tech Director

Signature


CL350K0
2016 Harley Ultra Limited
1971 Ford F100 Flareside (project)
2016 Ford Expedition
2018 Ford F150

Statistics


Total Posts
Total Posts
378
Posts Per Day
1.70
Albums
Total Albums
1
Total Photos
6
General Information
Last Activity
11-10-2019 01:28 PM
Join Date
04-04-2019
Referrals
0